High-Intensity 120 Watt Surface Mount LED Underwater Transom Light
$199.95 – $224.95
- Easy Install: All you have to do is drill 2 small 1/8″ holes in the back of the boat and surface mount the lighthead to the back of the transom. Then run the wires through the holes and connect the positive wire to the positive battery terminal and the negative wire to the negative battery terminal on a 12V battery.
- High-Intensity: Incredibly bright and affordable, we by far offer the highest lumen per dollar ratio in the underwater lighting industry for transom lights. Look at the table in the product pictures for more information. Read more below how lumen output is dependent on LED color.
- Long-Lasting: Built with high-quality materials, these will last for years of underwater submersion. Built with (40) 3 Watt LEDs totaling 120 Watts, our LEDs last for over 40,000 hours. With proper minimal maintenance, this light will last a lifetime.
- Fish Attractant: Lure all sorts of aquatic life right up next to your fishing boat. Green attracts the most fish.
- Dual Color Options: Available in dual-color variants, you can choose two colors giving you two colors of LEDs one on each side of the lighthead. You can either blend them or run them separately.
High-Intensity Surface Mount 40 LED Underwater Transom Light
Introducing our Surface Mount LED Underwater Transom Light designed specifically for easy surface mounting to the stern of your boat. We design this light to be incredibly bright, affordable, waterproof, corrosion-proof, durable, and long-lasting. Say goodbye to through-hull drilling. All you have to do is drill 2 small 1/8″ holes in the back of the boat.
Design
In this light, we use Cree 3535 LEDs soldered directly to a copper board. The board is thermally-adhered to a 6061 machined aluminum solid block. To wire up the light, we use military-grade Teflon wire that is incredibly durable and corrosion-proof. To seal the lighthead, we epoxy embed it inside of an attractive gray 4.5″ diameter flanged PVC flush mount fitting that is only 2″ tall. To seal the lighthead fully, we seal the front of the lighthead with an indestructible Lexan lens.
High-Intensity
Built with (40) 3 Watt LEDs, this light is incredibly bright for the cost. Here at Loomis LED, we have the industry-leading lumens per dollar cost amongst all other underwater lighting companies transom lights. Look above at the table in the product pictures for more information. Lumen output is dependent on LED color. For another option, we also sell a 24 LED Surface Mount Transom Light.
Shining a High-Intensity Green Underwater Transom Light into the woods.
Lumen output by color
- White produces 180 lumens per LED * 40 = 7200 lumens
- Green produces 130 lumens per LED * 40 = 5200 lumens
- Aqua produces 110 lumens per LED * 40 = 4400 lumens
- Red produces 90 lumens per LED * 40 = 3600 lumens
- Blue produces 50 lumens per LED * 40 = 2000 lumens
Fish Attractant
Lure fish right up to your boat with this 40 LED underwater transom light. Phytoplankton feed on the light during the night as a food source. Other fish and aquatic life will then come to feed on the phytoplankton. Similar to chum, the light acts as an underwater fish feeder. Night fishing has never been easier with this high-intensity boat transom light. Use these lights for nighttime fishing of bait, tuna, swordfish, and striped bass. Green attracts fish the best followed by aqua, white, blue, and then red. To learn more, read our article, “Why do Underwater Lights Attract Fish?”
Boat Size Light Purchasing Recommendations
Depending on boat size, we recommend purchasing either 1, 2, 3, or 4 transom lights for optimal light spread across the back of the boat. For boats <20′ we recommend either two 24 LEDs or two 40 LEDs. For boats >20′ you can purchase anywhere from 2 to 4 lights depending on the beam width of the transom. Make sure your lights are as deep as possible below the waterline rather than far apart.
2 Aqua 40 LED Transom Lights
Surface Mount Easy Installation
To mount, you only have to drill 2 small 1/8″ holes in the back of the transom. Next, surface mount the transom lights and run the wires through. Simply connect the positives to the positives and the negatives to the negatives on a 12 VDC non-charging or charging battery. More detailed installation instructions are in our downloads section of our website.
Maintenance
To maintain, rinse off the saltwater after boating as it will corrode the metal slowly when it is exposed to air. Additionally, coat the PVC with a thin layer of waterproof marine grease to greatly reduce or eliminate marine growth and only require a monthly periodic reapplication. Make sure the lights are never operated out of the water as overheating can still damage the LEDs. In addition, make sure to turn off lights when on a plane as they are don’t have direct water cooling. If you follow these steps, your light will last a lifetime of use.
Includes
- (1) – Loomis LED High-Intensity Surface Mount 40 LED Underwater Transom Light
- (1) – Built-in thermal protection switch will turn off light at 120° F
- (2) – #6×1″ stainless steel screws
- (1) – 22′ – 24′ of expensive 22 AWG military-grade Teflon M27500 cable.
- (1) – 4.5″ dia x 2″ high flanged PVC surface mount fitting light assembly
- (1) – 2-year warranty
Warranty
We include a 2-year warranty with this surface mount LED underwater transom light. The warranty is voided if the cable is shortened or damaged, or it experiences lightning/electrical damage.
Submit your review | |
| Color | Aqua, Blue, Dual Color: Blue/Green, Dual Color: Blue/White, Green, Red, White |
|---|
Specifications
40 led flush mount gray transom light (12-14.5 vdc only)
- Size: 4.5”dia x 2”h
- Wire: 22 feet 22awg mil spec teflon cable
- (2) 6-32 stainless mounting screws supplied
- Color: Green, Aqua, Blue,Red or White
- Lumens: 5200 green, 3600 Aqua, 1700 blue, 4800 white
- Watts: 60
- Current: 5 Amps
Warranty: 2 years excludes return shipping.
Installation Instructions: Two small mounting holes need to be drilled for each light. I recommend 3M 5200 on screw threads before screwing in mounting screws. Wires can be fed through existing transducer holes, over the transom or a small ¼ inch hole drilled above waterline for feeding wires into hull.
For cooling purposes lights are designed to be underwater during operation.
Submit your review | |
Reviews (0)
Your email address will not be published. Required fields are marked *
Be the first to review “High-Intensity 120 Watt Surface Mount LED Underwater Transom Light”
You must be logged in to post a comment.
Related products
- High Intensity: 48 incredibly bright – 3 Watt LEDs for a total of 144 Watts in white, green, aqua, or blue. The lumen output of this light varies depending on the LED color. Read our color section below to learn more.
- Plug N’ Play: Plug into a standard 110 VAC outlet and throw this off the boat, dock, pool, etc. and watch this illuminate a 360° circle around the light.
- Fish Attractant: Aquatic life is drawn to underwater lights. Phytoplankton feed on light, ultimately, drawing higher members of the aquatic food chain to the light.
- Submersible: With a transformer, we can do longer cable lengths up to 125'. For fishing boats with 110 VAC outlets, these lights can be hooked up to go deeper than our battery-powered fishing drop lights.
- Multiple Applications: Can be dropped off the dock, boat, pool, or anything underwater. All it requires is a 110AC outlet.
- Quality Materials: (4) 36 Watt LED boards, crystal clear temperature-grade epoxy, heavy-duty vinyl end cap for protection, stainless wire eyelet for attaching float or chum bag, and up to 125' of 18 AWG heavy duty SJOOW cable with embedded strain relief.
- Long-Lasting: We run our LEDs at lower power leading to a longer lifetime. We do this because LEDs get most of their lumens at 60 - 70% input power, leading to lower electrical costs, reduced operating temperatures, and longer lifetimes. The indestructible lighthead is fully epoxy embedded, with heavy-duty marine-grade cable.
- Portable: Runs off (2) lightweight Samsung commercial-grade 3 amps/hr, 18650 lithium-ion batteries. Other gigging lights on the market require you to carry around a 12V battery, making this incredibly lightweight and easy-to-use. The lighthead only weighs 12 ounces and the PVC shaft weighs 6 ounces. Together it weighs slightly over a pound.
- High-Intensity: Puts out 1200 lumens in bright white from a Cree XML L2 LED chip. Even in less than ideal murky water, this light will illuminate a huge area equivalent to 1 of your car headlights on high.
- Capacity: About 2 hours of run-time for non-stop flounder gigging. Additional batteries can be purchased if 2 hours isn't long enough for your use.
- Multipurpose: Can be used for casting, trolling, or anywhere a high-powered waterproof high-intensity light source is needed.
- Fish Attractant: Use this light for nighttime gigging of flounder, frog, shrimp, etc. Fish are attracted to light during the night.
- Color: We use bright white because it is proven to be the best for flounder gigging.
- High-Intensity: Built with (24) or (40) 3 Watt high power LEDs totaling 72 and 120 Watts, this light is incredibly bright. Our LED underwater dock lights offer unparalleled lumen per dollar ratios in the underwater lighting industry. Read more about how lumen output per color varies below.
- Plug N’ Play: Simply tie a 6″ by 6″ patio paver to the bottom of the light, plug into a standard 110 AC outlet, and heave. The light will sink to the bottom and illuminate a huge diameter of light in a 140° beam.
- Submersible: Completely submersible, this underwater light is intended for water deeper than 10' or shining out from your dock when mounted.
- Energy-Efficient: Replace those expensive metal halide/mercury vapor bulbs with cheaper energy-efficient LED underwater dock lights. Costs roughly 10 to 25 cents a day to run these lights at 4 hours a night.
- Long-Lasting: Durable and built to last, LEDs last for over 30,000 hours of run time. Built with high-quality materials, these lights are simply indestructible. Failing to adhere to our instructions is the only way for these lights to fail. We offer a 2-year warranty because we stand behind our USA manufactured products.
- Versatile: Used for saltwater docks, freshwater docks, fixed docks, floating docks, and even your swimming pool. As long as there are a water source and a standard 110 AC outlet this light will work anywhere. Mountable to dock pilings.
- Safety: Operating on safe low voltage DC current, there is no need to worry about electrical runoff. We use high-quality AC to DC Meanwell transformers so you can swim carefree.
- Easy Install: Simply drill 2 small 1/8″ holes in the back of the boat and surface mount the lighthead to the back of the boat transom.
- High-Intensity: Incredibly bright and affordable, we offer the highest lumens per dollar ratio in the underwater transom lighting industry. We offer 6 times more lumens for the cost than our closest competitor. Look at the table in the product pictures for more information. Lumen output is dependent on color. Read more below to decide your color.
- Long-Lasting: Built with high-quality materials, these will last for years of underwater submersion. Built with (24) 3 Watt LEDs totaling 72 Watts, our LEDs last for over 40,000 hours. With proper minimal maintenance, this light will last a lifetime.
- Fish Attractant: All sorts of aquatic life will be drawn to this light. Phytoplankton are attracted to underwater lights at night as a food source. In turn, other members of the food chain will come to feed on the phytoplankton.
- Dual Color Options: Available in dual-color variants, we offer two colors of LEDs one on each side of the lighthead. You can either blend them for a 3rd color or run them separately depending on what you want.
- Depth-Adjustable: Can be custom adjusted to specific depths to be right above mud or sediment on the bottom. To use, tie wrap a weight to the cord and that will act as the anchor point to how high the light will float.
- High-Intensity: Incredibly bright and affordable, we offer the industry-leading lumen per dollar ratio. The light shoots a 140° beam angle from the 40 LED/ 120 Watt light head. The deeper the light the larger the diameter of light spread on the surface. Our lumen output per color is shown below.
- Fish Attractant: Lure aquatic life right up next to your dock. Phytoplankton feed on the light which in turn brings all other members of the food chain.
- Versatile: Can be used for floating docks, fixed docks, saltwater docks, and freshwater docks. Intended for water deeper than 10' and/or murky water at the bottom. All you need is a 110 Ac standard outlet and a water source.
- Plug N' Play: Simply plug into a 110 AC outlet and heave this off the dock!
- Safe: We use safe low voltage AC to DC transformers to ensure there is no risk of electrocution while swimming.
- High-Intensity: Incredibly bright and affordable, our LED underwater dock lights offer unparalleled lumen per dollar ratios in the underwater lighting industry. Available in 24 LEDs at 72 Watts or 48 LEDs at 144 Watts. Read more about lumen output per color below.
- Plug N' Play: Just plug into a standard 110 AC outlet and tie an 8" by 8" patio paver to the bottom of the light and heave. The light will sink to the bottom and illuminate a huge diameter of light in a 360° beam.
- Shallow Water: Illuminates in a 360° beam angle to illuminate a wider circle in shallow waters less than 10 feet deep. Fully submersible, and designed to be run exclusively underwater.
- Energy-Efficient: These will cost roughly 10 to 25 cents a day to run these lights. Replace those expensive metal-halide/mercury vapor bulbs with drastically higher electrical costs, with energy-efficient LED underwater dock lights.
- Long-Lasting: Durable and built to last, our light will last a lifetime of use. Conservatively, LEDs will last for around 30,000 hours of use. The only way these lights will fail is by failing to adhere to our instructions.
- Versatile: Used for freshwater docks, saltwater docks, floating docks, fixed docks, and even your swimming pool. As long as there is both a water source and a standard 110 AC outlet this dock light will work anywhere.
- Safety: These operate on safe low voltage direct current due to our high-quality AC to DC transformers. There is no need to worry about electrical runoff.
- Submersible: 40% of light is reflected off the water when using an out of water pool light, Epoxy embedded and designed to last a lifetime in the pool.
- High-Intensity: 12 - 3 Watt LEDs for a total of 36 Watts. This light is so much brighter than other lighting options on the market. Each color puts out differing lumen amounts:
- Blue: 50 * 12 = 600 lumens
- Aqua: 110 * 12 = 1320 lumens
- Green: 130 * 12 = 1560 lumens
- White: 180 * 12 = 2160 lumens
- Easy-to-Install: Just hang the wire loop around the coping of the pool and this light is plug and play.
- Energy-Efficient: Replace the costly halogens and lower electrical costs with LEDs.
- Color Options: Available in Aqua, Blue, Green, White, Red, and Amber.
- Wide Beam Angle: 140° beam angle with water refraction disperses light spread around the pool for even light dispersion.
There are no reviews yet.